Advanced Thermoplastic Composites
SkillBridge program
CCM Machine Operator
Post Falls, Idaho61 - 90 daysIn-person
Specific MOCs — see eligibility
About the program
Program ObjectiveThis 12-week program trains transitioning service members to safely and independently operate Continuous Compression Molding (CCM) equipment used in composite laminate production while meeting aerospace-quality manufacturing standards.The trainee will progress from safety fundamentals to full independent machine operation with documented competency validation.
What you'll do
Week 1 – Safety & Compliance OrientationFocus: Workplace safety and manufacturing fundamentalsTraining Topics:
- Facility orientation
- PPE requirements
- Heat and pressure hazard awareness
- Lockout/Tagout (LOTO)
- Chemical handling procedures
- Environmental and company compliance policies
- Introduction to AS9100 quality awarenessPerformance Objectives:
- Demonstrate proper PPE usage
- Perform LOTO procedure under supervision
- Pass safety knowledge assessment (minimum 85%)Supervision Level: Direct supervisionEvaluation Method: Written quiz + practical demonstration________________________________________Week 2 – CCM Process FundamentalsFocus: Understanding materials and documentationTraining Topics:
- Continuous Compression Molding process overview
- Composite materials (resin systems, fibers, laminates)
- Reading setup cards and work instructions
- Basic blueprint/drawing interpretation
- Introduction to HMI interfacePerformance Objectives:
- Correctly interpret setup card
- Identify key machine components
- Navigate HMI screensSupervision Level: Direct supervisionEvaluation Method: Supervisor observation checklist________________________________________Week 3 – Machine Setup (Assisted)Focus: Assisted machine preparationTraining Topics:
- Heating die preparation
- Building stackups
- Loading creels
- Startup and shutdown proceduresPerformance Objectives:
- Assist with 3 machine setups
- Identify correct temperature and pressure parameters
- Follow startup checklist without omissionSupervision Level: Direct supervisionEvaluation Method: Setup checklist sign-off________________________________________Week 4 – Machine Operation (Assisted)Focus: Parameter control and monitoringTraining Topics:
- Adjusting temperature, pressure, and speed
- Alignment verification
- Monitoring HMI for consistency
- Material feeding techniquesPerformance Objectives:
- Perform parameter adjustments under supervision
- Maintain stable production run for minimum 2 hours
- Document production data correctlySupervision Level: Close supervisionEvaluation Method: Production run review________________________________________Week 5 – Introduction to Quality ControlFocus: In-process inspectionTraining Topics:
- Thickness measurement
- Dimensional verification
- Surface finish inspection
- Visual defect identificationPerformance Objectives:
- Inspect 5 production samples
- Correctly identify common laminate defects
- Complete inspection report accuratelySupervision Level: Close supervisionEvaluation Method: Quality Manager review________________________________________Week 6 – Documentation & TraceabilityFocus: Production and quality documentationTraining Topics:
- Batch records
- Traceability requirements
- Nonconformance reporting process
- Shift turnover communicationPerformance Objectives:
- Complete full batch record independently
- Accurately document inspection data
- Conduct simulated shift turnover briefingSupervision Level: Moderate supervisionEvaluation Method: Documentation audit________________________________________Week 7 – Independent Setup (Supervised)Focus: Increased responsibilityTraining Topics:
- Full machine setup
- Parameter verification
- Pre-production checklist validationPerformance Objectives:
- Complete 1 full setup with minimal assistance
- Verify all machine parameters correctly
- Meet setup time standard within 15%Supervision Level: Observation with intervention as neededEvaluation Method: Supervisor competency checklist________________________________________Week 8 – Production Monitoring & Process StabilityFocus: Maintaining consistent qualityTraining Topics:
- Process drift recognition
- Thickness variation causes
- Surface defect root causes
- HMI trend monitoringPerformance Objectives:
- Maintain stable run for full shift
- Identify 2 simulated process deviations
- Escalate issues appropriatelySupervision Level: ObservationEvaluation Method: Production metrics review________________________________________Week 9 – Troubleshooting FundamentalsFocus: Process issue identificationTraining Topics:
- Common CCM failures
- Alignment issues
- Temperature drift
- Material feed problemsPerformance Objectives:
- Diagnose 2 process issues
- Recommend corrective action
- Document issue reportSupervision Level: Guided troubleshootingEvaluation Method: Supervisor review________________________________________Week 10 – Preventative MaintenanceFocus: Equipment care and contamination preventionTraining Topics:
- Preventative maintenance schedule
- Die cleaning procedures
- Component inspection
- Reporting mechanical concernsPerformance Objectives:
- Participate in 2 PM cycles
- Perform supervised die cleaning
- Complete maintenance checklist accuratelySupervision Level: Moderate supervisionEvaluation Method: Maintenance log verification________________________________________Week 11 – Independent Operation (Observed)Focus: Full operational responsibilityResponsibilities:
- Machine setup
- Parameter control
- In-process inspection
- Documentation completion
- Shift reportingPerformance Objectives:
- Meet production rate within 10% of standard
- Zero safety violations
- Complete full documentation packageSupervision Level: Observation onlyEvaluation Method: Performance evaluation_______________________________________Week 12 – Final Qualification & AssessmentFocus: Demonstrated competencyEvaluation Includes:
- Full independent machine setup
- 4-hour monitored production run
- Quality inspection verification
- Documentation audit
- Troubleshooting scenarioQualification Standard:
- No critical errors
- 100% documentation accuracy
- Meets safety and quality expectationsOutcome:Upon successful completion, trainee is qualified for independent CCM Machine Operator duties.
Eligibility
Target military occupations
Army: 91 series Navy: MM, EM, HT Air Force: 2A7X, 3E1X, 3E5X Marines: 13XX, 21XX Coast Guard: MK
- Ability to lift 50 lbs
- Ability to stand for extended periods
- Must meet vision requirements for quality inspection
- Must be eligible to work in CUI/CMMC‑aligned environments post‑service
- Must complete TRP requirements per DoD policy
Good to know
MOUs on file